61% off- Physics
- Ready-made model
- Class 10 to 12
- Printed report included
Mini Step-Up Transformer Science Project Physics Working Model with Report
Code B0G2T964L6
- Paid for and delivered by Amazon or Flipkart. The current price and the delivery date for your PIN code are shown there.
- Sold by Gurukul Technicals Institute, Delhi.
- Need a different topic, a custom version or a school order? Ask on WhatsApp.
In this project guide
Ready-made model
About this model
This physics working model is a low cost mini step-up transformer that runs on a 9 V battery. When the push button is pressed, a relay switches the battery current on and off rapidly through the low-voltage side of a small 6-0-6 transformer used the other way round, and the stepped-up output lights a tiny neon-type lamp. The listing calls it a series step-up transformer and says a report is included.
How it works
The science behind it
The idea the model demonstrates, in words you can use in your report and when you explain it.
A transformer works on mutual induction. A changing current in one coil produces a changing magnetic flux in the iron core, and this changing flux induces an emf in the other coil (Faraday's law). For an ideal transformer, Vs ÷ Vp = Ns ÷ Np, so the winding with more turns gives the higher voltage. A transformer does not work on steady DC, because a constant current gives no change in flux. This model gets round that with a relay used as an interrupter. When the button is pressed, current flows through the relay coil and the transformer's low-voltage winding; the relay pulls its contact open, the current stops, the contact springs back and the cycle repeats many times a second, which is why it buzzes. Each sudden break makes the flux collapse quickly, and the winding with far more turns, the one normally connected to the mains, gives out high-voltage pulses. These light the neon lamp, which needs much more than 9 V to glow.
Make it yourself
Make a battery-powered mini step-up transformer yourself
Build your own version from scratch, or use the steps to understand how the ready-made model is put together before you present it.
What you need 9
Step by step 9 steps
- Find the two windings
The high-voltage (mains) winding has two wires, and the 6-0-6 winding has three. If unsure, ask an adult to check with a multimeter's resistance range; the high-voltage winding reads much higher.
Fix the transformer, relay, push button and battery snap on the base, leaving the lamp at the far end.
Wire the relay as an interrupter: battery positive to the push button, the button to the relay's common (COM) contact, the normally closed (NC) contact to one end of the relay coil, and the other end of the coil to battery negative.
Connect the 0 wire and one 6 wire of the transformer's low-voltage winding across the relay coil, so the winding gets the same on-off current.
If you use the capacitor, connect it across the relay coil with its negative lead to the battery negative side.
Connect the neon lamp across the two wires of the high-voltage winding, and cover every joint on that side with tape or sleeving.
Do not fit a diode across the relay coil: it would swallow the sudden voltage that the transformer steps up.
Snap on the battery and press the button. The relay should buzz and the lamp should glow. Release the button as soon as you have seen it.
Label each part, and keep the lamp in view but its wires out of reach.
Read this first
Safety first
Go through these points before you build or switch anything on. Younger students should do this with an adult.
- The high-voltage winding gives out pulses far above 9 V. Never touch its wires, the lamp leads or any joint on that side while the button is pressed, and release the button before touching anything.
- Never connect any part of this transformer to a wall socket; the model runs only from the 9 V battery.
- Never short the battery terminals, and remove the battery after use.
- Solder only with an adult present, and rest the hot iron on its stand.
Troubleshooting
If something does not work
The usual problems with this model and how to fix them. Open a problem to see the fix.
The relay clicks once and stays pulled in
It is wired through the normally open (NO) contact, so it never breaks its own current. Move that wire to the normally closed (NC) contact.
The relay buzzes but the lamp does not glow
Check that the lamp is on the high-voltage winding and the 6 V winding is across the relay coil. Remove any diode across the coil and fit a fresh battery.
Nothing happens when I press the button
Check the battery, the snap and the button, and that the far end of the relay coil really goes to battery negative.
The battery runs down quickly
The relay and the transformer winding draw a fair current. Press the button for a few seconds at a time and remove the battery after use.
Exhibition day
How to present it
A running order for the exhibition table or the practical, step by step.
Draw the circuit on a chart: battery, push button, relay interrupter, the low-voltage (6-0-6) winding as the primary, and the high-voltage winding with the lamp as the secondary.
Explain the step-up from the transformer's rating: the winding made for the mains has many times more turns than the low-voltage winding, so it gives a much higher voltage. Do not probe the output with a meter.
Explain why the core is laminated and name the main losses: copper loss, eddy current loss, hysteresis loss and flux leakage.
Keep fingers away from the output terminals while it is working, because a step-up transformer gives out a higher voltage than it receives.
Practice
Viva questions
Practice questions on this model, with short answers. Try each one aloud before you open the answer.
Which phenomenon makes a transformer work?
It works on mutual induction: a changing current in one coil induces an emf in a nearby coil linked by the same magnetic flux.
What would happen if a steady DC supply were connected to the primary?
No emf would be induced in the secondary, except for a brief moment when switching on or off, because steady DC gives a constant flux.
How can this model run a transformer from a 9 V battery?
The relay works as an interrupter: it switches the battery current on and off many times a second, so the flux keeps changing and an emf is induced in the other winding.
When a transformer steps up voltage, what happens to the current?
In an ideal transformer the current is stepped down in the same ratio, so that Vp × Ip equals Vs × Is.
Project file
Project file outline
The headings of the project file, in order. Give each heading its own section and write it in your own words.
The listing includes a printed project report: use this outline to check that your own file covers every part.
Free ebook: Writing a Science Project FileContents
- Aim: to make a low cost mini step-up transformer that lights a neon lamp from a 9 V battery
- Apparatus
- Theory: mutual induction, the turns ratio and why a transformer needs a changing current
- Circuit diagram: battery, push button, relay interrupter, transformer and lamp
- Working of the relay as an interrupter
- Observations: the lamp glows only while the button is pressed and the relay buzzes
- Result
- Precautions
- Uses of step-up transformers at power stations
Buying checklist
Before you buy
What to check before you order the model.
1Check these first
- Transformers are studied in senior secondary physics under alternating current; ask your teacher what explanation they expect at your level.
- The model runs on a 9 V battery, as the photos show; check whether a battery comes with it, and carry a spare.
- Its output gives high-voltage pulses that light the lamp; these must not be touched while the button is pressed.
- The listing says a report is included; add your own circuit diagram and observations so the file matches your model.
- Try the model with an adult a few days before the exhibition.
- Keep the box to protect the transformer, relay and lamp.
- Check the delivery date for your PIN code on the marketplace, and order well before the exhibition or practical.
- Practise explaining it. Judges ask what the model shows and why; knowing the science matters as much as the model. The viva questions above are a good place to start.
Next steps
Take it further
Ways to turn this model into a bigger investigation or a stronger exhibition entry.
Compare the relay's make-and-break action with an electric bell, which uses the same idea to keep its hammer moving.
Find out how the same make-and-break idea was used in the ignition coil of older cars to make the spark at the spark plug.
Remove the capacitor, if fitted, and note how the buzzing and the glow change.
Audience
Who it suits
Suits Class 12 physics investigatory projects on electromagnetic induction and alternating current, and Class 10 science exhibitions.
- ClassClass 10 to 12
- SubjectPhysics
- TypeReady-made model
- Project reportPrinted report included
Free to read
Free ebooks for this topic
Free PDF ebooks from Gurukul Technicals Institute on the science, the making and the presenting of projects like this one.
- Free PDF ebook
Electricity and Magnetism Experiments
Hands-on experiments with cells, wires, bulbs and magnets
- Free PDF ebook
Physics Working Models Explained
Twenty classic models, how each works and how to make it
- Free PDF ebook
Your Science Exhibition Guide
Choose a project, build it, present it and answer the judges with confidence
- Free PDF ebook
Writing a Science Project File
How to write the report, from the cover page to the bibliography








