43% off- Physics
- Class 10 to 12
Bridge Rectifier Educational Circuit Board
Code B07MZDQXLD
- Paid for and delivered by Amazon. The current price and the delivery date for your PIN code are shown there.
- Sold by Gurukul Technicals Institute, Delhi.
- Need a different topic, a custom version or a school order? Ask on WhatsApp.
In this project guide
Physics
About this model
This educational circuit board demonstrates a bridge rectifier, the four-diode circuit that turns alternating current (AC) into direct current (DC). The photo is small, but it appears to show a board edged with green tape, a circuit drawn on pink paper with the four diodes in a diamond, a part with wires at the top left and a cord with a plug along the bottom edge.
How it works
The science behind it
The idea the model demonstrates, in words you can use in your report and when you explain it.
A p-n junction diode conducts when it is forward biased and blocks current when it is reverse biased. In a bridge rectifier, four diodes are arranged in a diamond. During one half cycle of the AC input, two diagonally opposite diodes conduct; during the next half cycle, the other two conduct. Both times the current passes through the load in the same direction, so both halves of the wave are used, which is called full wave rectification. The output is pulsating DC, and with India's 50 Hz supply the pulses come at 100 Hz. A capacitor across the output charges near each peak and discharges slowly between them, smoothing the ripple. Because the current always passes through two silicon diodes, each dropping about 0.7 V, the output peak is about 1.4 V less than the input peak. A step-down transformer is normally used first to reduce the mains voltage to a low, safer value. Every mobile charger contains a rectifier doing this same job.
Make it yourself
Make a bridge rectifier circuit board yourself
Build your own version from scratch, or use the steps to understand how the ready-made model is put together before you present it.
What you need 9
Step by step 8 steps
Draw the circuit on the chart: the AC input on the left, the four diodes in a diamond in the middle, and the capacitor and output LED on the right.
Place the four diodes in a diamond so that two bands (cathodes) meet at the positive output corner and two plain ends meet at the negative output corner; the two remaining corners are the AC input.
Solder the diodes to screw terminals or a small circuit board fixed on the base, following the drawing.
Connect the LED with its 1 kΩ resistor across the output, with the LED's long leg towards the positive corner.
Connect the capacitor through its slide switch across the output, with its positive leg to the positive corner.
First test with the 9 V battery: connect it to the two AC corners one way and then the other way round. The LED should light both times, which proves the output polarity never changes.
An adult then connects the low-voltage AC adapter to the AC terminals and plugs it in. Measure the AC input and the DC output with the multimeter, first with the capacitor switched out and then with it switched in.
Ask the adult to unplug the adapter, let the capacitor discharge through the LED, and then label each part on the chart.
Read this first
Safety first
Go through these points before you build or switch anything on. Younger students should do this with an adult.
- Use only a ready-made low-voltage AC adapter, plugged in by an adult; never connect the board directly to the mains and never open the adapter.
- If your board has its own plug and transformer, only an adult should plug it in, and nobody should touch the board or its wires while it is plugged in.
- Fit the electrolytic capacitor the right way round and use one rated at least 25 V; a reversed or under-rated capacitor can bulge or burst.
- Unplug the supply before changing any connection, and never short the 9 V battery.
- Solder only with an adult, and keep the hot iron in its stand.
Troubleshooting
If something does not work
The usual problems with this model and how to fix them. Open a problem to see the fix.
The LED lights with the battery one way round but not the other
One diode in the bridge is open or badly soldered, so only one pair can conduct. Check each joint and test each diode with the multimeter's diode range.
A diode gets hot, or the LED stays off both ways round
A diode is probably reversed, which shorts the supply through the bridge in one direction. Unclip the battery, or have the adult unplug the adapter, at once, then correct the diode's direction against the drawing.
The DC reading is negative
The multimeter probes are swapped. Put the red probe on the corner where the two bands meet.
Switching in the capacitor makes no difference
It may be disconnected, reversed or faulty. Check the switch and its polarity; a working capacitor raises the DC reading towards the peak voltage.
Exhibition day
How to present it
A running order for the exhibition table or the practical, step by step.
Before switching on, find out from your teacher what supply the board needs, and let only an adult connect anything to a socket.
Trace the current path for each half cycle with arrows of two different colours on a chart.
Draw the AC input wave and the pulsating DC output one above the other, to show that the negative halves are turned over, not lost.
Compare the bridge with a half wave rectifier: number of diodes, shape of the output and efficiency.
Practice
Viva questions
Practice questions on this model, with short answers. Try each one aloud before you open the answer.
Why is a bridge rectifier called a full wave rectifier?
It uses both halves of every AC cycle, sending each half through the load in the same direction.
How many diodes conduct at a time in a bridge rectifier?
Two diodes conduct at a time, one diagonal pair in each half cycle.
What is the ripple frequency of the output for a 50 Hz input?
It is 100 Hz, because there is one output pulse for every half cycle.
What does the filter capacitor do?
It charges near each peak and discharges between peaks, making the pulsating output much steadier.
Project file
Project file outline
The headings of the project file, in order. Give each heading its own section and write it in your own words.
Free ebook: Writing a Science Project FileContents
- Aim: to convert AC into DC using a bridge rectifier
- Introduction: AC, DC and why electronic devices need DC
- The p-n junction diode in forward and reverse bias
- Working of the bridge rectifier in each half cycle
- Circuit diagram, with the input and output waveforms
- The filter capacitor and ripple
- Observations: AC input and DC output, with and without the capacitor
- Comparison with half wave and centre-tap rectifiers
- Conclusion, precautions and bibliography
Buying checklist
Before you buy
What to check before you order the model, and what to do when it arrives.
1Before you order
- Check that rectifiers are part of your syllabus and what your teacher wants shown.
- The listing gives no power details, so ask what supply the board uses; the small photo seems to show a cord with a plug, so plan for an adult to connect it.
- Practise drawing the input and output waveforms and the current path in each half cycle.
- Keep the box and carry the board flat so the parts and wires are not bent.
- Check the delivery date for your PIN code on the marketplace, and order well before the exhibition or practical.
2When it arrives
- Test the board with an adult as soon as it arrives, well before the practical or exhibition.
Next steps
Take it further
Ways to turn this model into a bigger investigation or a stronger exhibition entry.
Add a 7805 regulator IC after the capacitor to get a steady 5 V output, and measure it.
Build a half wave rectifier with one diode and compare its DC output with the bridge's.
View the input and output waveforms on a CRO in the school lab with your teacher.
Audience
Who it suits
Suits Class 12 physics investigatory projects and practicals on semiconductor diodes, and diploma students learning about power supplies.
- ClassClass 10 to 12
- SubjectPhysics
Free to read
Free ebooks for this topic
Free PDF ebooks from Gurukul Technicals Institute on the science, the making and the presenting of projects like this one.
- Free PDF ebook
Electricity and Magnetism Experiments
Hands-on experiments with cells, wires, bulbs and magnets
- Free PDF ebook
Physics Working Models Explained
Twenty classic models, how each works and how to make it
- Free PDF ebook
Your Science Exhibition Guide
Choose a project, build it, present it and answer the judges with confidence
- Free PDF ebook
Writing a Science Project File
How to write the report, from the cover page to the bibliography








